T40高位消防水箱使用维护说明书.doc

使用维护说明书T4120高位消防水箱目录directory1.设备名称与型号Equipment name and model number2.用途与适用范围Purpose and scope of application3.技术参数、结构形式与工作原理Technical parameters, structure and working principle3.1总体The overall3.2主要部件1Main part 13.3主要部件2Main part 24.设备的安装和调试Equipment installation and debugging5.操作和使用Operation and use 6.维护保养与故障排除Maintenance and troubleshooting6.1设备的维护和保养Equipment maintenance and maintenance6.1.1日常维护和保养The daily maintenance and maintenance6.1.2 定期维护和保养Regular maintenance and maintenance6.2设备常见故障与处理办法Equipment mon faults and processing methods6.2.1 机械元部件常见故障A mon failure of mechanical ponents7.附件The attachment罐体结构图Structure of tank1.设备名称与型号Equipment name and model number设备名称：高位消防水箱规格型号：7500×2000×1500mm.Device name: high fire water tank Specifications:7500*2000*1500mm.2.用途与适用范围Purpose and scope of application高位消防水箱用于储存消防用水,水箱为方形平底封闭贮箱,箱体顶部焊一圈加强筋,箱内作加强处理；配就地显示液位计；顶部开人孔并加盖板,同时配置箱内爬梯.high fire water tank used to store fire water, square flat closed tank, water tank for system.after the weld a ring stiffeners, in strengthening treatment; With local display liquid level meter; At the top of the open manhole and top cover plate, and at the same time the gym in the cabinet.3.技术参数Technical parameters3.1总体overall技术规范表：Technical specification sheet:项目project单位unit数据<number>备注note设备台数Equipment sets台<number>1设备尺寸 equipment sizemm7500*2000*1500设备容积volumem318设计压力Design pressure0.1Mpa运行压力Operatingpressure常压<Atmospheric pressure>运行温度Operating temperature常温normal temperature材质materialSS304技术要求：高位消防水箱为SS304不锈钢材质焊接的方形水箱.分片交货；需在国内开料、打坡口按标准、成型、涂底漆,分类包装,分片规格按设备制造图的规定进行.高位消防水箱本体上设人孔一个,并配扶梯； 液位计选用玻璃管就地显示液位计；本体设有下列接口：进水、溢流、出水、呼吸、排污与备用接口.Technical requirements:high fire water tank for SS304 stainless steel welding square tank. Fragmentation of delivery; Needs to open the door at home, a groove <according to the standard>, molding, primer, classification of packaging, shard specifications in accordance with the provisions of the equipment manufacture drawing. high fire water tank manhole a is set on ontology, and escalators;level gauge glass tube in situ show that the level;body is equipped with the following interface: water, Mouth breathing, flooding, water, sewage, and the standby interface.工作原理：贮存消防用水,高位消防水箱指符合规范要求的静压满足最不利点消火栓水压的水箱,利用重力自流供水,设置在建筑的最高处,静压不能满足最不利点消火栓水压时,应设增压稳压设施.临时高压消防给水系统必须设置消防水箱,系统平时仅能满足消防水压而不能保证消防用水量.发生火灾时,通过启动消防水泵提供灭火用水量.Working principle:Storage fire water, high fire water tank refers to conform to the requirements of the specification of static pressure to meet the most unfavorable point of fire hydrant water pressure tank, using gravity artesian water, installed in the building, the highest point of static pressure can not meet the most unfavorable point fire hydrant water pressure, should set pressure regulated facilities. Temporary high-pressure fire water system must be set fire water tank, usually can only meet the fire water system and cannot ensure fire water consumption. A fire, the fire flow through start the fire pump.3.2主要部件13.2 main part1高位消防水箱high fire water tank1本体ontology外形尺寸：Overall dimensions：7500*2000*15000有效容积Effective volume：18m3材质：SS304Material：SS304台 set12UPVC液位计UPVC level gauge玻璃管液位计:DN25Glass tube liquid level Meter：DN25个Set13进水口Water inletDN50,PN1.0个Set14溢流口overflow mouthDN100,PN1.0个Set15出水口outletDN150,PN1.0个Set16排污口drainDN100,PN1.0个Set17手动阀液位计配套Supporting manual valve <level meter>DN25,PN1.0个Set28备用口Spare mouthDN50,PN1.0个Set19呼吸口Mouth breathingDN50,PN1.0个Set13.3主要部件23.3 main part 2高位消防水箱high fire water tank1人孔<单台>Manhole <single>数量 number个set1人孔规格Manhole specificationsmm700*700人孔材质Manhole materialSS3044.设备的安装和调试基础可采用混凝土条形梁,或工字钢. 组合式不锈钢水箱顶部对角设有透气空气过滤装置,规格和数量根据进口尺寸大小由用户确定装置.组合式不锈钢水箱 内部均使用拉筋.各管口法兰均为1.0MPa标准法兰.在布置组合式不锈钢水箱位置时,应参照GB17051-1997二次供水设施卫生规范.组合式不锈钢水箱 规格技术参数或方位与实际使用不适合时,由不锈钢水箱设计人员按实际需要提出确定.4. Equipment installation and debuggingBasic bar concrete beams can be used, or beams. Modular stainless steel water tank at the top of the diagonal with breathable air filter device, the specification and quantity according to import size to determine the device by the user. Modular stainless steel water tank using the brace. All the pipe flange is 1.0 MPa standard flange. In the arrangement of modular stainless steel water tank, the secondary water supply facilities should consult GB17051-1997 health. Modular stainless steel water tank specifications and technical parameters or the bearing and the actual use, right by the stainless steel water tank According to the actual needs to be put forward to determine the design personnel.5.操作和使用设备在投入使用前,应清理内部污物,除去水箱表面的毛刺防止员工在操作时刮伤,设备在使用前,安装单位应检查所有联接螺栓的紧固情况确保连接合适,牢固,待管道连接好后一起做严密性试验.5. Operation and useInternal dirt before put into use, the equipment should be clean, remove the burr on the surface of the water tank prevent employees from scratch during operation, equipment before use, installation unit should check all the connecting bolt fastening connection suitable, solid, after waiting for pipe connection good do leak test together6.维护保养与故障排除6.1设备的维护和保养6.1.1 日常维护和保养每天检查高位消防水箱周围管路的密封性,若有出现泄漏现象应与时修补.6.1.2 定期维护和保养每月应检查安全阀是否灵活、畅通.检查罐身是否有腐蚀、破损并与时修补.检查螺丝是否松动和失效.每年检查焊缝是否牢固、密封圈是否老化.每年对罐体油漆一遍做防锈处理.6.2设备常见故障与处理办法6.2.1 机械元、部件常见故障阀门故障和排除方法：1阀杆转动不灵原因：1、填料压得过紧.2、阀杆与其他配合不为的损伤或积有污物.3、开关次数过多.排除方法：1、松动阀杆螺母重新调整.2、拆开修整与清除污物.3、拆开清晰排除污物.2阀座与阀体之间有渗漏原因：1、预紧力不够.2、密封面有损伤或者污物.3、密封面变形或者失效.排除方法：1、增加预紧力.2、修整或者研磨密封面并清除污物.3、更换密封圈.3结合部法兰处漏液原因：1、结合部法兰螺栓松动.2、结合部垫片损坏或失效.排除方法：1、拧紧螺栓.2、更换结合部垫片.6. Maintenance and troubleshooting6.1 equipment maintenance and maintenance6.1.1 the daily maintenance and maintenanceDaily check of high fire water tank surrounding pipeline sealing, if there is leakage phenomenon should be repaired in a timely manner.6.1.2 regular maintenance and maintenanceEvery month should check the safety valve is flexible and open. Check whether there is body corrosion, damage and repair in time. Check whether the screw is loose and failure. Annual inspection of weld is rigid, sealing ring is aging. Every year to do antirust processing tank paint again.6.2 equipment mon faults and processing methods6.2.1 machinery yuan, mon fault ponentValve failure and elimination method:1> stem in ironsReason: 1, too tightly on the packing. 2, the valve stem and cooperate to be not to damage or other product with dirt. 3, switch too many times.Method: 1, loosen stem nut to adjust. 2, open repair and remove dirt. 3, clear open drainage.2> there is leakage between seat and bodyReason: 1, the pre-tightening force is not enough. 2, the sealing surface damage or dirt. 3, sealing surface deformation or failure.Method: 1, increase pre-tightening force. 2, nap or ground sealing surface and remove dirt. 3, replace the seal ring.3> the integration of the flange leakageReason: 1, the integration of flange bolt is loose. 2, integration of gasket damage or failure.Method: 1, screw down the bolt. 2, the integration of a replacement gasket.7.附件罐体结构图7. The attachmentStructure of tank